Fuel Level Gauge With Stainless Steel Bezel
  • Fuel Level Gauge With Stainless Steel Bezel
  • Rear of Gauge
  • Gauge 5 Wire Wiring Loom
  • Gauge With Wiring Loom Plugged In

Fuel Level Gauge 240 to 33 ohm with Stainless Steel Bezel

A classically styled 52mm fuel level gauge with a shiny stainless steel bezel. This fuel level gauge is compatible with fuel senders that are 240 ohms when empty and 33 ohms when full such as Teleflex, Faria USA and Vetus.

Add to your basket...

Fuel Level Gauge with Stainless Steel Bezel - 240 to 33 Ohm (EC632)

Price:
£23.50
SRP:
£29.36
You save:
£5.86 (20%)
Quantity:

Fuel Level Gauge 240 to 33 ohm with Stainless Steel Bezel Information

The Fuel Level Gauge 240 to 33 ohm with Stainless Steel Bezel is a classically styled black gauge with white writing, an analogue white needle and a shiny stainless steel bezel, it is also waterproof, perfect for classic boats such as Freeman Cruisers.

The fuel level gauge has a scale from Empty (E) to Full (F) with markings for 1/4, 1/2 and 3/4 full to show the amount of fuel in your tank. The gauge requires an appropriate sender to be fitted to the fuel tank to sense the correct fuel level.

Fuel Level Gauge Senders - What Resistance?

This fuel level gauge works with a sensor that reads 240 ohms of resistance when the tank is empty and 10 ohms when the tank is full. This type of fuel sender is usually used by American gauge manufacturers and may be found on boats of American origin here in the UK. Common gauges using this resistance to show empty and full could be made by Beede, Faria USA, Medalion, S. Giorgio Sein, Teleflex and Vetus.

This classic fuel level gauge comes complete with built-in led backlight illumination in either yellow or red light and is designed for use on 12 volt or 24 volt systems. It also comes complete with a wiring loom with a quick connect plug to make fitting easier.

Waterproof Fuel Level Gauge

This voltmeter gauge has an IP (Ingress Protection) rating of IP67 which means it is completely sealed from dust and is waterproof as it is protected against temporary immersion in water (up to 30 minutes).

Voltmeter Gauge with Stainless Steel Bezel Installation

The gauge requires a 53mm hole and will fit panels with a thickness from 0.5mm to approximately 20mm, this is achieved thanks to the long threaded body and large plastic nut to lock the voltmeter in position.

The wiring loom is pre-wired to a plug which pushes into the back of the gauge, only four wires are required, Positive, Negative, Sender and then either of the backlight wires, which can also be put through a switch to provide day time (yellow light) and night time (red light) illumination.

Fuel Level Gauge 240 to 33 ohm with Stainless Steel Bezel Specification

Voltage 12v or 24v
Scale Empty - 1/4 - 1/2 - 3/4 - Full
Display Analogue Needle
Dial Colour Black
Text Colour White
Signal 240 (Empty) to 33 Ohms (Full)
(Usually used by American Manufacturers)
Sender Compatibility Teleflex, Faria USA, Vetus, S. Giorgio Sein, Beede, Medalion
Diameter 57mm
Cut Out Diameter 52mm
Depth 62mm
Depth With Plug 67mm
Minimum Clearance Behind 55mm
Dashboard Thickness 0.5mm to 20mm
Illumination Yellow or Red
Connections 5 Wires on Multi Plug
Wire Length 38cm
Body Material Plastic

Included in the Fuel Level Gauge 240 to 33 ohm with Stainless Steel Bezel

  • 1 x Fuel Level Gauge
  • 1 x Wiring Loom
  • 1 x Resistor for 24v

You may also like...

Explore similar items...